 |
R404a
12V
VALEO TM16
135mm
A2
60 days
20
12 Months
This TM16-type heavy-duty refrigeration compressor is configured with a 12V electromagnetic clutch, a A2 twin-groove belt pulley, and a 135 mm pulley diameter. It is an aftermarket replacement option for selected R404A transport refrigeration and mobile cooling systems.
It is supplied for professional repair channels, compressor distributors, importers and fleet-maintenance purchasing programs. A correct selection requires comparison of the original label, clutch voltage, belt drive, pulley measurement, mounting ears and port layout.
This version gives buyers a defined TM16-family configuration rather than a generic compressor-body match. Its 12V clutch, A2 belt drive and 135 mm should be checked as one set against the removed unit.
TM16-family identification is only the starting point: mounting and port details still decide suitability. The product should not be chosen from a photograph alone because similar housings can be supplied with different clutch coils, pulley profiles and pulley offsets.
Elecdura can review original label images, pulley measurements and photographs of the mounting and ports before a wholesale quotation is prepared.
Matching principle: model family, voltage, belt drive and pulley diameter must all agree before mounting and port details are reviewed.
| Specification | Product Details |
Compressor Type | TM16 Type |
Clutch Voltage | 12V |
Pulley Type | A2 |
Number of Pulley Grooves | 2 |
Pulley Diameter | 135 mm |
Refrigerant Reference | R404A System Configuration |
Application Category | Transport Refrigeration and Mobile Cooling Systems |
Supply Type | Aftermarket Replacement / Wholesale B2B Supply |
The stated 12V rating applies to the electromagnetic clutch coil. A 12V clutch must be used with the matching 12V electrical control circuit.
A visually similar 24V clutch compressor is not an electrical substitute. Incorrect voltage can cause non-engagement, unreliable operation or coil damage.
This product uses a A2 twin-groove belt pulley. The A2 arrangement uses two A-profile belt grooves. Confirm the original belt section, groove count and belt alignment; A2 is a different drive interface from PV8, B1 and B2 configurations.
Compare the original belt type with the pulley face and confirm that the belt runs in the same plane as the installation bracket.
Measure the outer edge of the original pulley and compare it with the 135 mm specification. Include pulley offset and belt alignment in the inspection, not diameter alone.
A matching pulley profile with a different diameter can change belt speed and positioning. The original assembly remains the selection reference.
Compatibility cannot be confirmed by the TM16 family name alone. Review the complete electrical, belt-drive and physical configuration before ordering.
Confirm that the original compressor is a TM16-family unit, not a TM21 or another look-alike family.
Verify the original electromagnetic clutch is rated 12V.
Confirm the A2 pulley profile and 2-groove arrangement.
Measure the pulley outer diameter and confirm 135 mm.
Check pulley offset, belt alignment and bracket clearance.
Compare mounting ears, bolt positions and overall mounting geometry.
Compare suction and discharge port positions, head shape and port orientation.
Confirm the original system refrigerant, lubricant specification and oil quantity requirements.
Recommended matching information: send the original compressor label plus front, rear, side and pulley-view photographs before a bulk order.
When a label is damaged or incomplete, photographs with a visible pulley measurement and mounting details provide useful comparison evidence. Final fitment remains subject to the complete compressor and refrigeration-unit configuration.
This TM16-type 12V compressor is intended for selected belt-driven mobile refrigeration systems requiring the A2 drive and 135 mm pulley configuration.
Refrigerated trucks and vans
Cold-chain delivery vehicles
Mobile refrigeration units
Fleet maintenance and repair projects
Aftermarket compressor distribution programs
These are application categories, not guaranteed vehicle or unit fitment. The original label, voltage, drive, mounting and port arrangement must be verified before installation.
For mixed-configuration orders, separating models by clutch voltage and pulley drive prevents avoidable receiving errors. Order details can be reviewed against the agreed product specification before shipment.
TM16 family confirmation
12V clutch specification confirmation
A2 pulley profile and 2-groove inspection
135 mm pulley-diameter check
Visible mounting and port-layout review
Port protection, product appearance and packaging review
Inspection scope, photographs and documentation can be agreed according to order quantity and buyer requirements.
Elecdura supplies TM16-type refrigeration compressors to parts wholesalers, importers, distributors, fleet-service businesses and professional repair channels.
Specification matching from labels, photographs and measurements
Sample-order review before volume purchasing
Mixed-model quotation for compatible compressor requirements
Neutral packaging and labeling discussion
Pre-shipment photograph and packing-information review
MOQ, samples, packaging options and lead time are confirmed against the final model list, quantity and supply conditions.
No. The clutch coil voltage must match the system electrical circuit. A voltage mismatch can prevent correct clutch operation and may damage electrical components.
Do not assume interchangeability. This compressor requires a A2 2-groove drive; belt profile, groove count, pulley offset and alignment must match the removed unit.
Measure across the outer edges of the original pulley at its widest point, then compare the reading with 135 mm. A photograph showing the measuring tool is useful for a matching review.
No. Refrigerant reference is only one selection point. Compressor family, clutch voltage, belt drive, pulley size, mounting, ports and lubricant requirements must also be compatible.
Please provide the original label, front and rear photographs, a pulley photo with voltage and diameter details, mounting and port images, quantity and destination country.
This TM16-type heavy-duty refrigeration compressor is configured with a 12V electromagnetic clutch, a A2 twin-groove belt pulley, and a 135 mm pulley diameter. It is an aftermarket replacement option for selected R404A transport refrigeration and mobile cooling systems.
It is supplied for professional repair channels, compressor distributors, importers and fleet-maintenance purchasing programs. A correct selection requires comparison of the original label, clutch voltage, belt drive, pulley measurement, mounting ears and port layout.
This version gives buyers a defined TM16-family configuration rather than a generic compressor-body match. Its 12V clutch, A2 belt drive and 135 mm should be checked as one set against the removed unit.
TM16-family identification is only the starting point: mounting and port details still decide suitability. The product should not be chosen from a photograph alone because similar housings can be supplied with different clutch coils, pulley profiles and pulley offsets.
Elecdura can review original label images, pulley measurements and photographs of the mounting and ports before a wholesale quotation is prepared.
Matching principle: model family, voltage, belt drive and pulley diameter must all agree before mounting and port details are reviewed.
| Specification | Product Details |
Compressor Type | TM16 Type |
Clutch Voltage | 12V |
Pulley Type | A2 |
Number of Pulley Grooves | 2 |
Pulley Diameter | 135 mm |
Refrigerant Reference | R404A System Configuration |
Application Category | Transport Refrigeration and Mobile Cooling Systems |
Supply Type | Aftermarket Replacement / Wholesale B2B Supply |
The stated 12V rating applies to the electromagnetic clutch coil. A 12V clutch must be used with the matching 12V electrical control circuit.
A visually similar 24V clutch compressor is not an electrical substitute. Incorrect voltage can cause non-engagement, unreliable operation or coil damage.
This product uses a A2 twin-groove belt pulley. The A2 arrangement uses two A-profile belt grooves. Confirm the original belt section, groove count and belt alignment; A2 is a different drive interface from PV8, B1 and B2 configurations.
Compare the original belt type with the pulley face and confirm that the belt runs in the same plane as the installation bracket.
Measure the outer edge of the original pulley and compare it with the 135 mm specification. Include pulley offset and belt alignment in the inspection, not diameter alone.
A matching pulley profile with a different diameter can change belt speed and positioning. The original assembly remains the selection reference.
Compatibility cannot be confirmed by the TM16 family name alone. Review the complete electrical, belt-drive and physical configuration before ordering.
Confirm that the original compressor is a TM16-family unit, not a TM21 or another look-alike family.
Verify the original electromagnetic clutch is rated 12V.
Confirm the A2 pulley profile and 2-groove arrangement.
Measure the pulley outer diameter and confirm 135 mm.
Check pulley offset, belt alignment and bracket clearance.
Compare mounting ears, bolt positions and overall mounting geometry.
Compare suction and discharge port positions, head shape and port orientation.
Confirm the original system refrigerant, lubricant specification and oil quantity requirements.
Recommended matching information: send the original compressor label plus front, rear, side and pulley-view photographs before a bulk order.
When a label is damaged or incomplete, photographs with a visible pulley measurement and mounting details provide useful comparison evidence. Final fitment remains subject to the complete compressor and refrigeration-unit configuration.
This TM16-type 12V compressor is intended for selected belt-driven mobile refrigeration systems requiring the A2 drive and 135 mm pulley configuration.
Refrigerated trucks and vans
Cold-chain delivery vehicles
Mobile refrigeration units
Fleet maintenance and repair projects
Aftermarket compressor distribution programs
These are application categories, not guaranteed vehicle or unit fitment. The original label, voltage, drive, mounting and port arrangement must be verified before installation.
For mixed-configuration orders, separating models by clutch voltage and pulley drive prevents avoidable receiving errors. Order details can be reviewed against the agreed product specification before shipment.
TM16 family confirmation
12V clutch specification confirmation
A2 pulley profile and 2-groove inspection
135 mm pulley-diameter check
Visible mounting and port-layout review
Port protection, product appearance and packaging review
Inspection scope, photographs and documentation can be agreed according to order quantity and buyer requirements.
Elecdura supplies TM16-type refrigeration compressors to parts wholesalers, importers, distributors, fleet-service businesses and professional repair channels.
Specification matching from labels, photographs and measurements
Sample-order review before volume purchasing
Mixed-model quotation for compatible compressor requirements
Neutral packaging and labeling discussion
Pre-shipment photograph and packing-information review
MOQ, samples, packaging options and lead time are confirmed against the final model list, quantity and supply conditions.
No. The clutch coil voltage must match the system electrical circuit. A voltage mismatch can prevent correct clutch operation and may damage electrical components.
Do not assume interchangeability. This compressor requires a A2 2-groove drive; belt profile, groove count, pulley offset and alignment must match the removed unit.
Measure across the outer edges of the original pulley at its widest point, then compare the reading with 135 mm. A photograph showing the measuring tool is useful for a matching review.
No. Refrigerant reference is only one selection point. Compressor family, clutch voltage, belt drive, pulley size, mounting, ports and lubricant requirements must also be compatible.
Please provide the original label, front and rear photographs, a pulley photo with voltage and diameter details, mounting and port images, quantity and destination country.
This TM16-type heavy-duty refrigeration compressor features a 12V electromagnetic clutch, A2 pulley and 135 mm pulley diameter. It is supplied as an aftermarket replacement option for selected R404A transport refrigeration and mobile cooling systems.
The product is intended for refrigerated-vehicle repair businesses, compressor distributors, importers and wholesale replacement programs. Before ordering, buyers should compare the original compressor label, clutch voltage, pulley profile, pulley diameter, mounting points and suction and discharge port arrangement.
This heavy-duty A/C compressor is configured for buyers looking for a TM16-type replacement with a 12V clutch and A2 belt-drive arrangement. The 135 mm pulley diameter provides a clearly defined configuration that should be compared with the original compressor before installation.
Although different TM16-type compressors may use a similar housing, their voltage, pulley profile and pulley diameter can vary. A 12V A2 version should therefore not be selected only by its external appearance or compressor-family name.
Elecdura supports specification-based product matching for professional buyers. Original compressor photographs, label information and pulley measurements can be reviewed before a wholesale quotation is prepared.
| Specification | Product Details |
Compressor Type | TM16 Type |
Clutch Voltage | 12V |
Pulley Type | A2 |
Number of Pulley Grooves | 2 |
Pulley Diameter | 135 mm |
Refrigerant | R404A |
Application Category | Transport Refrigeration and Mobile Cooling Systems |
Product Type | Aftermarket Replacement Compressor |
Supply Type | Wholesale and B2B Supply |
The 12V specification refers to the voltage of the compressor electromagnetic clutch. It must correspond with the electrical system used by the refrigerated vehicle or transport refrigeration unit.
A visually similar 24V compressor should not be used as a direct replacement for this 12V version. Incorrect clutch voltage may prevent proper clutch engagement or damage the clutch coil and related electrical components.
This compressor uses an A2 pulley configuration. The designation indicates a two-groove A-profile belt arrangement rather than an eight-groove multi-rib pulley.
Before ordering, check the original belt profile, groove count and pulley alignment. An A2 pulley should not be treated as interchangeable with PV8, B1 or B2 configurations, even when the compressor body belongs to the same TM16 family.
The pulley has a specified outer diameter of 135 mm. Buyers should measure the original compressor pulley across its outer edges and compare the result with this product specification.
Pulley diameter is an important matching detail. Two TM16-type compressors may share the same voltage and pulley profile but still use different pulley diameters or pulley offsets. The original system configuration should therefore remain the main selection reference.
Compressor compatibility cannot be confirmed from the TM16 name alone. Buyers should compare the complete technical and physical configuration of the original unit with the replacement product.
Confirm that the original compressor belongs to the TM16 family.
Check that the electromagnetic clutch is rated for 12V.
Confirm that the original pulley uses an A-profile, two-groove arrangement.
Measure the pulley outer diameter and confirm that it is 135 mm.
Verify that the refrigeration system uses R404A.
Compare the compressor mounting ears and bolt positions.
Compare the suction and discharge port positions.
Check the cylinder-head shape and port orientation.
Confirm pulley offset and belt alignment with the mounting bracket.
Verify the required lubricant and oil quantity for the system.
Recommended matching information: Please send the original compressor label together with front, rear, side and pulley-view photographs before placing a bulk order.
When the original label is damaged or incomplete, detailed photographs and measurements can provide additional information for product comparison. Final compatibility remains subject to confirmation of the complete compressor and refrigeration-unit configuration.
This TM16-type 12V compressor is intended for selected belt-driven mobile refrigeration systems that require an A2 pulley, 135 mm pulley diameter and R404A-compatible configuration.
Potential application categories include:
Refrigerated trucks
Refrigerated vans
Cold-chain delivery vehicles
Mobile refrigeration units
Transport refrigeration repair projects
Fleet maintenance and replacement programs
Aftermarket compressor distribution
These application descriptions are general references rather than guaranteed vehicle or refrigeration-unit fitment. The original compressor label, voltage, pulley, mounting and port configuration must be checked before installation.
For distributors and importers, receiving the correct voltage and pulley configuration is particularly important when several TM16 variants are purchased together. Order details should therefore be confirmed before production or shipment.
Depending on the order requirements, the following product details can be included in the pre-shipment verification process:
TM16 compressor-family confirmation
12V clutch specification confirmation
A2 pulley-profile and groove-count inspection
135 mm pulley-diameter measurement
Pulley rotation and visible-condition checking
Mounting-ear and bolt-position comparison
Suction and discharge port-layout confirmation
Port sealing and protection inspection
Product appearance and packaging review
Batch-configuration consistency checking
Inspection scope, photographs and documentation can be discussed according to the order quantity, target market and buyer requirements.
Elecdura supplies TM16-type refrigeration compressors to automotive and refrigeration parts wholesalers, importers, distributors, fleet service businesses and professional repair channels.
Wholesale purchasing support may include:
Product matching based on labels, photographs and measurements
Sample-order review before larger-volume purchasing
Bulk quotation for distributors and importers
Mixed purchasing with other TM16 and TM21 configurations
Neutral packaging options
Customized packaging review according to order quantity
Product-label and carton-label coordination
Pre-shipment photograph and packing-information review
MOQ, sample availability, packaging options and production lead time are confirmed according to the final product specification, order quantity and current supply conditions.
No. The electromagnetic clutch voltage must match the electrical system used by the refrigerated vehicle or refrigeration unit. A 12V clutch should not be directly connected to a 24V system, and a 24V clutch may not engage correctly in a 12V system.
No direct interchangeability should be assumed. An A2 pulley uses a two-groove A-profile belt arrangement, while a PV8 pulley uses an eight-groove multi-rib belt. The belt profile, groove count, pulley diameter and pulley alignment must all match the original system.
Measure the outer diameter of the original compressor pulley across its widest point. The measurement should be compared with the 135 mm specification of this product. A clear photograph showing the measuring tool and pulley can also be sent to Elecdura for review.
No. R404A is only one part of the matching process. The compressor family, clutch voltage, pulley profile, pulley diameter, mounting arrangement, port position, lubricant and operating requirements must also be compatible with the original system.
Please provide the original compressor label, front and rear photographs, pulley photograph, clutch voltage, pulley diameter, mounting details, port arrangement, refrigerant, required quantity and destination country. This information supports a faster and more accurate product review.
Mixed-model purchasing can be discussed for selected TM16 and TM21 configurations. Availability, MOQ, packaging and production lead time should be confirmed according to the final product list and order quantity.
